The content in the next paragraphs about A Step-by-Step Guide to Installing a Bathtub is definitely interesting. Read it for yourself and decide what you think about it.
Installing a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the task can move rapidly; if you need to open up a wall to eliminate the old tub and also place the new bathtub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already purchased a brand-new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and product list need to consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the supply of water and also check all joints and brand-new pipework for leakages and tighten them if required. Load the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final position.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealer can split relatively early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that page on How to Install a Bathtub Yourself when doing a lookup on the web. Sharing is good. Helping others is fun. Thank you for your time spent reading it.
This Resource